Topic: 想問....... |
 Print this page
|
| 想問....... | Copy to clipboard |
|
Posted by: Geforce Posted on: 2003-07-04 13:32 想問有無問題??? thx 36"缸 | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: catlee Posted on: 2003-07-04 14:41 同我個缸size 一模一 !! 見你兩上兩下出水, 估你用4000L或以上泵, 用來直推冷水太勁, 可能要好長時間先可以降溫, 因水停係水冷 heat exchange 唔夠耐, 水未凍晒便走, 出翻主缸又會熱翻. 另外, 個櫃得36", 扣埋d木板得34"幾, sump 20" 及留泵位 (6" 起碼), 得番9"....邊度有chiller 咁細? 一係唔好用上水泵做水流, 一上出二, 主缸再加個潛水頭. 底上水又用潛水頭, 咁你就可將chiller 放入櫃. 重有, 櫃深得14"架渣, 個chiller 要打橫係櫃旁出氣. 因為我已經賴晒野...:(, 百葉門唔夠散熱, 一定要打橫加風扇. 點解要留成6"俾個泵? 因為太短有機會同sump共振, 咁就好嘈. 遠d有條喉吸振, 就算用潛水頭我都用海綿放sump 底. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: qqleo Posted on: 2003-07-04 14:44 記得開風扇窿 吹 / 抽 水冷機 d 熱氣呀 ~ :) | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-04 14:46 水冷你用上水泵直推.. 怕唔怕水壓太大呀? 如果你買d係用膠水箱既水泠.. 真係有d怕會谷爆個水箱喎.. 上水條路做過分流加閘制再入水冷啦.. 令你個缸係想養乜? | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: catlee Posted on: 2003-07-04 14:47 如果chiller 放出便, 你想點都得啦.....:D | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-04 14:54 還有一30"缸....有無問題??? thx 我正在研究造30" or 36"......... | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: 岩礁園丁 Posted on: 2003-07-04 15:46 水冷萬萬不可放在柜內, 熱到爆炸, 制冷能力大打折扣, 我先頭都係咁, 加幾多風扇都冇用, 全日打開柜門都唔掂, 最後都係移番出柜外, | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-04 16:05 剛剛改完．．．．．． | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-04 16:07 ３０” | |
| Re: 想問....... | Copy to clipboard |
|
Posted by: KK Posted on: 2003-07-04 16:17 下次試下唔好save as 24bit color. 一係save as gif.. 咁會細好多.. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-04 20:19 o個底缸深10"夠唔夠??? o個櫃d木板應該幾寸厚??? thx | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: Wally Posted on: 2003-07-04 21:01 There is one fatal problem on your design. The pipeline go to tank's bottom is connected at the same level of main pipe. In case of power failure all water will drain to your sump and your floor. Pipeline go to tank's bottom should connect to the main pipe, above water surface, and add a vent port on the main pipe. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: 岩礁園丁 Posted on: 2003-07-04 21:25 上水喉途經太多90度及T曲, 會大幅抵消上水泵的馬力, 變成冇力, 除非用個大到無侖的上水泵, 除電費驚人之外, 亦又引出另一個問題, 就是沙缸的水流速度問題, 如濾材過密, 會扯空泵, 濾材太通, 過濾效能又大大降低, 弄巧反拙, 這點要認真考慮. 解決辦法, 上水泵袛負責過濾工作, 水流工作則由加裝潛水頭來做. 另外, 太多出水口, 你反而會很難掌握每出水口的流量, 除非每個出水口都有獨立球閥來個別調節. 少少個人意見, 希望幫到你 | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-04 22:04 To: Wally o甘即點樣呀~~~可唔可以在我的圖上改o下.......:D Thank you very much~~~:D To: 岩礁園丁 這圖的上水喉是暫時劃....到時用軟膠喉~~~:D Thank you very much~~~:D 如果我唔造水流o甘應該用幾大馬力的泵......3000L每小時夠唔夠??? | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: 岩礁園丁 Posted on: 2003-07-04 22:34 new : 要用到幾大的上水泵, 要因各種變數而定, 不能畫一決定, 例如, 同一型號的水泵, 在兩個不同的魚缸, 都會有不同的性能表現, 就算同一個缸, 只要有少少改動, 性能都會唔同咗, 總之, 條上水喉(由泵咀到主缸出水口)越順, 越少出水口, 就越好力, 相反越曲節, 越多出水口, 就越無力, 甚至, 出水口在主缸的高低位置不同, 亦有不同的力度, 越淺水, 越好力, 相反, 越深水, 越無力, 揚程高低, 亦影響很大. 解決辦法, 参考魚缸記錄各位魚友的個案, 觀察類似自己的方案, 來作出決定 但通常一個30或36吋魚缸, 以Iwaki為例, 大部份魚友都是用30-R至40-RX, 如想更力猛, 則可用40-R, 但流量會較少.正常來講, 唔駛用到55-R咁大. 努力, 必定成功............:) | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: Wally Posted on: 2003-07-04 23:11 New, something like this. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: 林哥仔 Posted on: 2003-07-04 23:23 沙缸反轉用...上水喉直上,落水喉先轉彎,咁出水會好力d,上到缸頂如想分四個出口就將四個出口放哂上面,底流用潛水頭,如果唔係底o個兩個會冇力(水會潮向最易的方向)水冷出水應回主缸,因水冷泵在第二隔就反回水冷機,可能只有一二隔凍(個人覺得)沙缸20吋做四隔中間仲要減六吋再減玻璃厚度你自己計下仲有幾多位剩 | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-05 11:29 唔該大家...... 如果o甘造有無問題??? 底缸得唔得??? | |
| 回覆： 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-05 12:08 林哥仔 wrote: 沙缸反轉用...上水喉直上,落水喉先轉彎,咁出水會好力d,上到缸頂如想分四個出口就將四個出口放哂上面,底流用潛水頭,如果唔係底o個兩個會冇力(水會潮向最易的方向)水冷出水應回主缸,因水冷泵在第二隔就反回水冷機,可能只有一二隔凍(個人覺得)沙缸20吋做四隔中間仲要減六吋再減玻璃厚度你自己計下仲有幾多位剩 不太讚成上水泵放係滴流位下.. 到時一下子有乜錯失個幾組滴流下既水路滴水燒泵咁就好弊.. 呢d野真係話唔埋.. 可能有人會話滴濕左搵野索番軟就得.. 但電器野.. 濕過咸水都唔多耐過啦.. 唔好為左博慳果兩個彎位.. 其實用軟喉或幾個四十五度曲都好幫得手. [color=red]令老友你好似仲未講你個缸係養乜喎.. FOT同RT個水路應係好唔同架..[/color] | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-05 15:18 珊瑚缸...... 底缸24"得嗎??? 30" | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-05 20:46 川記老闆答o西我d問題~~~~~:) 但我想問..... 如果有底缸......主缸d沙係唔係3"厚得??? 底缸要不要放沙???.......要幾厚??? Thank you~~~ | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-05 21:49 RT.. 沙缸乜鬼都唔洗啦.. 留個大位放支好skimmer.. 得既就養埋草.. 但小心草缸d光會照到你成個沙缸都係苔.. 主缸要唔要沙..除你.. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-06 19:27 1.底缸唔要放沙??? 我見好多底缸都有放沙~~~~:) 2.如果要放d沙是粗或幼??? 主缸d沙放粗或幼??? 3.珊瑚缸的底缸要唔要放珊瑚骨??? 4.要唔要加格仔板??? 圖中是我隨意畫...........如有問題請改~~~:) 5.水冷應買哪牌子??? 如果....日生650L好唔好用??? 6.請告訴我圖中1至6應放什麼??? 如果有成功的個案......請post d 圖給我參考~~~:) 請盡快回覆.......我要造啦!!!!! | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-07 19:29 更改~~~ Please help me.....:D Thank you!!! | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-07 19:31 點解唔上水泵加個T位分流去水冷既? | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-07 19:55 iczfirz 兄: 係唔係o甘呀..... Thank you~~~~:D | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-07 19:55 ..... | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-07 21:03 去水冷果條路記得加個閘制. | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: new Posted on: 2003-07-08 20:56 Thank you 我已訂了o個缸.....:D | |
| 回覆： 想問....... | Copy to clipboard |
|
Posted by: iczfirz Posted on: 2003-07-08 21:18 努力加油努力加油努力加油努力加油努力加油努力加油努力加油努力加油努力加油努力加油 | |
即時聊天廣播.
All Rights Reserved.
[Processing Time] User:0.12, System:0.01, Children of user:0, Children of system:0
請大家技持更換新主機啦, 多謝!